Lane Dividers are also tall and flexible enough so that they can suffer vehicle impacts without major damage to the divider or the vehicle.

Portable Separator and Guide Curb

One of the most common products you see on Australian roads today, the Guide Curb and Portable separator allow for easy installation, portable relocation and can be temporary or permanently fixed to the road.

• The single separator units are connected with a very solid moulded-in metal hook.
• The stable, but flexible connection guarantees enough clearance in order to setup different curves (90°-angle to about 11 x 11m).
• The manifold anti-slide system on the bottom of each unit ensures an excellent laying stability on the road surface. It can be easily exchanged after abrasion.
• The separator does not have to be glued or screwed to the road.
• In the contrary to road studs or road marking tapes, no residuals of glue are left on the lane. This aviods the danger of so-called phantom markings.
• Built-in one-size-fits-all slot accepts all RRSP Leitboy products.
• Lateral climbing edges allow vehicles firstly to climb on- and secondly to press down the separator whilst driving over. This aids position stability to the separator.
• The reflective arch with 14 cats’ eyes reflectors, depict the raised profile. This helps in particular motorcyclists to notice an elevation on the lane, especially at night.

Roundable Deliniator

• Early perception and recognition of obstacles in the darkness enable drivers to prepare for specific traffic situations
• The Leitboy delineator indicates a clear lane separation and guidance.
• The rubber flex foot allows the device to be impacted and then return to its orginal up-right position.
• Leitbys do not pop out when run over by cars.
• Recessed sheetings anels reduce possible damages of the reflective sheeting to a minimum.
• Flat and even surfaces on both sides provide best reflectivity.
• Retro reflective sheetings efficiently reflect vehicle’s headlights back to the direction of the vehicle.
• Reboundable uprights slide into place as close as every meter or 5 meters. Minimum distance is 10 meters for proper efficiency and acceptance for motorists.

Leitboy I (L42)

• One-piece unit
• Rubber flex body and foot (TPE)
• Recessed sheeting area
• Slanted sheeting, one side or two sides
• Sheeting type II, HIG
• Carrying handle
• Sheeting, center out availabe on request (Subject to minimum quantities)

Leitboy II (L72)

• Two-piece unit
• High impact resistant panel (PP)
• Rubber flex foot screwed to panel, exchangeable
• Recessed sheeting area
• Slanted sheeting, one side or two sides
• Sheeting type II, HIG
• Carrying handle
• Sheeting, center ut available on request (Subject to minimum quantities)

Leitboy III (L82)

• Two-piece unit
• High impact resistant panel (PP)
• Rubber flex foot screwed to panel, exchangeable
• Recessed sheeting area
• Slanted sheeting, one side or two sides
• Sheeting type II, HIG
• With or without carrying handle
• Sheeting center out available on request (Subject to minimum quatities)

Leitboy III

• High impct resistant panel (PP)
• Recessed sheeting area
• Slanted sheeting, one side or two sides
• Sheeting type II, HIG
• Steel bracket, screwed to panel, exhcnageable

Leitboy IV (L92)

• Two-piece unit
• Blow moulded high impact resistant panel (HDPE)
• Rubber flex foot screwed to panel, exchangeable
• Recessed sheeting area
• Slanted sheeting, one side or two sides
• Sheeting type II, HIG
• Carrying handle

Mini Leitboy L30 and L32

• Flexible plastic, orange
• Amber sheeting type II, HIG, 40x40mm
• Leitboy fixed to base by screwed brackets
• Base with cat’s eyes reflectors
• Can be positioned utilising either glue, glue mats or with asphalt/concrete bolts (Bolts/glue not incl.)

Mini Leitboy L30.2

• Flexible plastic, white
• Amber sheeting type II, HIG, 40x40mm
• Leitboy fixed to base by screwed brackets
• White base with cat’s eyes reflectors
• Can be positioned utilising either glue, glue mats or with asphalt/concrete bolts (Bolts/glue not incl.)

Mini Leitboy L32.2

• Flexible plastic, orange
• White sheeting type II, HIG, 40x40mm
• Leitboy fixed to base by screwed brackets
• Base with cat’s eyes reflectors
• Can be positioned utilising either glue, glue mats or with asphalt/concrete bolts (Bolts/glue not incl.